教你配置簡單的靜態路由

教你配置簡單的靜態路由

　　歡迎來到學習啦。這篇教你配置簡單的靜態路由是學習啦小編特地為大家整理的，希望對大家有所幫助!

　　為了更有說服力和便于理解我用CPT(Cisco Packet Tracer)演示了一下。

　　拓?fù)鋱D如下圖所示：

　　分別有四個網段，10.0.0.0/8、112.237.228.0/24、192.168.10.0/24、211.86.104.0/24。

　　靜態路由設置如下：

　　ip route 192.168.10.0 255.255.255.0 112.237.228.1 ip route 211.86.104.0 255.255.255.0 112.237.228.1 ip route 10.0.0.0 255.0.0.0 112.237.228.244 ip route 211.86.104.0 255.255.255.0 192.168.10.1 ip route 112.237.228.0 255.255.255.0 192.168.10.2 ip route 10.0.0.0 255.0.0.0 192.168.10.2

　　配置如下：

　　1.PC0的IP配置：

　　Packet Tracer PC Command Line 1.0

　　PC>ipconfig

　　IP Address......................: 10.0.0.3

　　Subnet Mask.....................: 255.0.0.0

　　Default Gateway.................: 10.0.0.1

　　PC>

　　2.PC1的IP配置：

　　Packet Tracer PC Command Line 1.0

　　PC>ipconfig

　　IP Address......................: 211.86.104.52

　　Subnet Mask.....................: 255.255.255.0

　　Default Gateway.................: 211.86.104.254

　　PC>

　　3.R1的配置：

　　Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#interface FastEthernet0/1 R1(config-if)#ip address 10.0.0.1 255.0.0.0 R1(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up R1(config-if)#end R1# %SYS-5-CONFIG_I: Configured from console by console R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int f0/0 R1(config-if)#ip addr 112.237.228.244 255.255.255.0 R1(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R1(config-if)#end R1# %SYS-5-CONFIG_I: Configured from console by console R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip route 192.168.10.0 255.255.255.0 112.237.228.1 R1(config)#ip route 211.86.104.0 255.255.255.0 112.237.228.1 R1(config)#end R1# %SYS-5-CONFIG_I: Configured from console by console R1#

　　4.R2的配置：

　　Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)# R2(config)#interface FastEthernet0/1 R2(config-if)#ip address 112.237.228.1 255.255.255.0 R2(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up R2(config-if)# R2(config-if)#exit R2(config)#interface FastEthernet0/0 R2(config-if)#ip address 192.168.10.2 255.255.255.0 R2(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R2(config-if)#end R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip route 10.0.0.0 255.0.0.0 112.237.228.244 R2(config)#ip route 211.86.104.0 255.255.255.0 192.168.10.1 R2(config)#end R2# %SYS-5-CONFIG_I: Configured from console by console R2#

　　5.R3的配置：

　　Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R3 R3(config)# R3(config)#interface FastEthernet0/1 R3(config-if)#ip address 192.168.10.1 255.255.255.0 R3(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up R3(config-if)# R3(config-if)#exit R3(config)#interface FastEthernet0/0 R3(config-if)#ip address 211.86.104.254 255.255.255.0 R3(config-if)#no shutdown R3(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R3>enable R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip route 112.237.228.0 255.255.255.0 192.168.10.2 R3(config)#ip route 10.0.0.0 255.0.0.0 192.168.10.2 R3(config)#end R3# %SYS-5-CONFIG_I: Configured from console by console R3#

　　6.使用tracert進行測試：

　　測試從PC0能否路由到PC1。

　　結果表明測試成功。

　　測試從PC1能否路由到PC0。

　　結果表明測試成功。